Worm Gear Sets A33

Worm Gear Set A33
dimensions worm gear sets a33
Legende
i = gear ratio da1 = tip diameter (worm) T2 = output torque
γm = Lead angle z2 = No. of teeth MF = mineral grease
mn = module dm2 = pitch diameter (worm gear) MÖ = mineral oil / synthetic grease
z1 = number of threads dA = max. diameter (worm gear) SÖ = synthetic oil
dm1 = pitch diameter (worm)
Axial distance 33 mm i Lead angle m Worm Worm gear T2 [Nm]
Shop Bronze
CAD-Data z1 dm1 da1 z2 dm2 dA MF
A33Ü3 3,5:1 25°57′ 1,75 6 24 27,5 21 42 47 10,1 12,1 15,1
A33Ü5 5:1 20°50′ 2 4 22,5 26,5 20 43,5 49 10,6 12,7 15,9
A33Ü7 7:1 15°32′ 1,5 4 22,4 25,4 28 43,6 48 12,2 14,6 18,3
A33Ü10 10:1 13°10′ 1,5 3 19,75 22,75 30 46,25 51 13,3 16 19,9
A33Ü11 11,33:1 10°42′ 1,3 3 21 23,6 34 45 49,2 13,3 16 19,9
A33Ü12 12:1 11°14′ 1,9 2 19,5 23,3 24 46,5 52 13,5 16,2 20,2
A33Ü14 14:1 7°20′ 1,5 2 23,5 26,5 28 42,5 47 11,4 13,7 17,1
A33Ü15 15:1 8°25′ 1,5 2 20,5 23,5 30 45,5 50 13 15,6 19,5
A33Ü16 16:1 10°1′ 1,5 2 17,24 20,24 32 48,76 53 14 16,8 21
A33Ü17 17:1 9°3′ 1,4 2 17,8 20,6 34 48,2 52,5 14,2 17 21,3
A33Ü18 18:1 6°57′ 1,25 2 20,65 23,15 36 45,35 49,2 12,6 15,1 18,9
A33Ü20 20:1 6°43′ 1,15 2 19,66 21,96 40 46,34 50,5 12,7 15,2 19
A33Ü24 24:1 5°27′ 1,9 1 20 23,8 24 46 51 13,2 15,8 19,8
A33Ü28 28:1 3°36′ 1,5 1 23,9 26,9 28 42,1 46,6 11,2 13,4 16,8
A33Ü30 30:1 4°8′ 1,5 1 20,85 23,85 30 45,15 50 12,7 15,2 19
A33Ü32 32:1 4°50′ 1,5 1 17,8 20,8 32 48,2 52,5 13,5 16,2 20,2
A33Ü38 38:1 3°55′ 1,25 1 18,26 20,76 38 47,74 51,6 13,9 16,7 20,8
A33Ü50 50:1 2°27′ 0,9 1 21 22,8 50 45 48 10 12 15
A33Ü56 56:1 2°10′ 0,8 1 21,15 22,75 56 44,85 48 10,1 12,1 15,1
A33Ü60 60:1 2°33′ 0,8 1 17,96 19,56 60 48,04 51,5 11,4 13,7 17,1
A33Ü72 72:1 1°30′ 0,6 1 22,8 24 72 43,2 46 8,4 10,1 12,6
A33Ü75 75:1 1°41′ 0,6 1 20,5 21,7 75 45,5 48 9 10,8 13,5

All worms and worm gears stocked right hand only.
Worm made of case hardened and ground steel (HV 620 – 700).
Worm gear made of CuZn37Mn3Al2PbSi-S40 or CuZn37Mn3Al2Si°. On request made of plastic or HGW 2083.

°Note:
Since July 21, 2021, the exceptions of the EU Directive 2011/65/EU (RoHS II) regarding the use of lead as an alloying element in steel (Exception 6a in Annex III) and in copper alloys (Exception 6c in Annex III) expire. In order to give our customers legal certainty with regard to the requirements of the RoHS directive, we have decided to gradually convert our standard worm gear sets to alloys with a lead content of ≤ 0.1% by weight (worm: 11SMn30 / worm wheel: CuZn37Mn3Al2Si).

You can find an up-to-date overview of the materials that have already been converted on the product pages in our online shop. You can recognize these by the ° marking and by the new item numbers without spaces (e.g. new: R17U80B° / e.g. old: R 17U 80B).

The output torque rating (T2) applies to the initial speed of 2800 rpm at the worm (shaft).
The efficiency values (see table in worm gear set catalog) are guidelines. The bearing, lubrication, speed, and installation, in addition to the lead angle, can influence efficiency.

Gears may be combined only with worms of the same axial distance and with the same transmission ratio.
Worms or worm gears from other manufacturers may not be paired with the counterpiece from Framo Morat. It is almost always necessary to adjust the toothing specifications.
All dimensions can be adapted upon request.

Is your desired gear set not available? Request your gear set!
Moderate quantities are usually available from stock, larger quantities are delivered in partial quantities or upon request.

Additional information

Contact person

Application examples

Worm Gear Sets overview

Worm Gear Sets